第1个回答 2009-08-07
Term of validity: On June 25, 2009 stops
the Zhejiang Province quality engineering supervision bureau to issue after due investigation
(2206) (Zhejiang) the quality monitoring to examine the character 144
term of validity: On June 25, 2009 stops
the Zhejiang Province quality engineering supervision bureau to issue after due investigation
the examination report
product range: The hanging automatic dried noodles fire-fighting unit
is examined the unit
to examine the category: The request examines
the Zhejiang Province fire prevention product quality examination to stand
the altogether 3 pages, first page of
product range: Hanging automatic dried noodles fire-fighting unit
specification model:
Is examined the unit
trademark:
The production unit
examines the category: The request examination
entrusts the unit:
Sampling cardinal number:
Sampling unit:
Production date: In December, 2008
samples the place:
Sampling date
sample quantity: 2
to type date: On December 30, 2008
sample serial number:
Examination date: On January 17, 2009 - 19th
examines the basis: GA602-2006 "Dried noodles Fire-fighting unit"
examines the project: Marking and viewing test, 20℃ spraying performance, fire-extinguishing sufficient load, fire-fighting unit intensity request, fire-fighting unit seal request, hand support (place) performance, fire extinguisher performance requirement
examination conclusion: "Dried noodles Fire-fighting unit" examines according to GA602-2006, this FZXA6/1.2 hanging automatic dried noodles fire-fighting unit is examining the project examination result to be qualified.
(Examination report special-purpose chapter) Zhejiang Province fire prevention product quality examination station examination service special-purpose chapter of
signing and issuing date on January 21, 2009
in note dried noodles fire-extinguishing monoammonium phosphate content nominal value 50%. The date of expiry is two years.
Authorization:
Verification:
Establishment:
The examination project
standard request
sample number
actual result
conclusion
symbolized and the viewing test
symbol
outward appearance
product label should clear, establish durably in the fire-fighting unit obvious spot.The content should include: The manufacture plant name or the trademark, the product range, the application temperature scope, fire fighting ability, the product serial number, carry out the standard, the fire-extinguishing type and the use term of validity, the fire-fighting unit install the request
fire-fighting unit the outside surface to be supposed to level, not obvious instrument damage or uneven phenomenon.The surface spreads, coating should even, the not obvious flow marking, scratch and so on the flaws
to conform to request
qualified
20℃ spraying performance
spraying time S
to spray surplus rate
by is not bigger than the 01.Mpa/s speed evenly as pressure-rise as the 2.Mpa hydraulic pressure, and maintains 5min, various parts will be supposed not to have flaws and so on leakage, macroscopic distortion or damage
install 1.54Mpa the nitrogen or the compressed air fire-fighting unit plunge to the water in, will install is not smaller than to the liquid level depth 0.3m, will maintain 5min, each connection spot will be supposed the non-air bubble divulging
fire-fighting unit hand support (place) in to withstand 5 time of fire-fighting unit quality and does not have to have the distortion in the fire-fighting unit spraying process or to escape the link, falls offPhenomenon
non-air bubble divulging
fire extinguisher performance requirement
monoammonium phosphate content
第2个回答 2009-08-04
Validity: 2009, June 25, 2007
Zhejiang quality technology supervision bureau issued
(2206) (zhejiang) quality supervision inspection word 144
Validity: 2009, June 25, 2007
Zhejiang quality technology supervision bureau issued
Inspection report
Product name: automatic suspension powder fire extinguishing devices
Client units
Inspection categories: entrust inspection
Zhejiang fire-fighting products quality inspection
3 pages, on the first page
Product name: automatic suspension powder fire extinguishing devices
Specifications:
Client units
Mark:
Production units
Inspection categories: entrust inspection
Entrust unit:
Sampling base:
Sampling unit:
Production date: December 2008
Sampling sites:
Sample date
Sample number 2:
To sample date: on December 30, 2008
Sample Numbers:
Inspection date: January 2009, 17-19
Inspection according to the GA602-2006: dry fire extinguishing devices"
The inspection items: logo and inspection, 20 ° c injection performance, extinguishant filling quantity, fire extinguishing equipment and strength requirement device sealing requirements, hanging bracket (seat) performance, MieHuoJi performance requirements
Conclusion: according to the test GA602-2006 "powder fire extinguishing devices, test, this FZXA6/1.2 type hanging type automatic powder fire extinguishing devices in screening program test results.
Special inspection report (zhejiang province) fire product quality inspection test format
The date of issue on January 21, 2009
Note container.during application of ammonium dihydrogen phosphate levels nominal values by 50%. Valid for two years.
Approval:
Review:
Preparation:
The inspection items
Standard requirement
Samples.
Test results
conclusion
Mark and inspection
mark
Appearance,
Signs should clear, durable and set fire on the device. Obviously Contents include: name of manufacturer or trademark, the product name, use temperature range, ability, product Numbers, standards, flame retardant type and validity, fire-fighting equipment installation requirements
The outer surface of the fire extinguishing devices should level off, without apparent equipment damage or uneven phenomenon. Surface coating, coating should be uniform, without apparent flow mark, scratch etc
Comply with the requirements
qualified
20 ° c injection performance
Injection time
Spray surplus rate
In not more than 01. Mpa/s rate uniformity to 2 Mpa pressure boost, and maintain 5min components should be no leakage and deformation and damage or other defects
The device 1.54 Mpa nitrogen or compressed air into the water into the fire extinguishing devices, equipment and liquid depth not less than 0.3 m, maintain, each part should be connected 5min without bubble leakage
Fire extinguishing devices suspension scaffolds (seat) five times in the fire-fighting equipment quality and in the process of spray fire-extinguishing devices are not deformation or ring, fall off
Without bleb leaking
MieHuoJi performance requirements
Ammonium dihydrogen phosphate levels
第3个回答 2009-08-03
楼主，这个真的超过我们的能力了。
我建议你找专业的来翻译吧。那样保险一点，否则很容易出错的。
第4个回答 2009-08-03
Duration: June 25, 2009 only
Issue of Quality and Technical Supervision of Zhejiang Province
(2206) (Zhejiang) 144 words Quality Supervision Inspection
Duration: June 25, 2009 only
Issue of Quality and Technical Supervision of Zhejiang Province
Inspection reports
Product Name: automatic suspension powder fire extinguishing installations
Tested units
Test Category: commissioning test
Zhejiang Product Quality Inspection Station Fire
A total of 3, the first page
Product Name: automatic suspension powder fire extinguishing installations
Specifications Model:
Tested units
Trademark:
Production units
Test Category: commissioning test
Commissioned units:
Sample base:
Sampling unit:
Production Date: December 2008
Sampling locations:
Sampling Date
The number of samples: 2
To the kind of date: December 30, 2008
Sample ID:
Inspection date: January 17, 2009 -19 Day
Test basis: GA602-2006 "dry powder fire extinguishing installations"
Test item: logo and appearance inspection, 20 ℃ jet performance, filling the volume of fire extinguishing agent, fire extinguishing installations strength, fire-fighting equipment sealing requirements, hoisting stent (Block), performance, performance requirements灭火机
Inspection Conclusion: In accordance with GA602-2006 "dry powder fire extinguishing installations" test, the automatic suspension FZXA6/1.2 type dry powder fire extinguishing installations where the seized items pass the test results.
(Seal inspection reports), Zhejiang Product Quality Inspection Station Fire Detection Business Seal
Date of issue January 21, 2009
Remarks dry powder fire extinguishing agent in ammonium dihydrogen phosphate content of the nominal value of 50%. Two-year validity period for.
Approval:
Audit:
Preparation:
Test item
Standards
No. samples
Measured results
Conclusion
Signs and exterior inspection
Logo
Appearance
Signs should be clear, durable and fire-fighting equipment installed in a clear position. Should include: manufacturer name or trademark, product name, the use temperature range, fire-fighting capacity, product code, the implementation of standards, the type of extinguishing agent and use of the validity of the installation requirements of fire fighting equipment
The outer surface of fire-fighting equipment should be flat and no significant equipment damage or uneven phenomenon. Surface coating should be uniform, no significant flow marks, scratches and other defects
To meet the requirements
Qualified
20 ℃ jet performance
S injection time
The remainder of the rate of injection
To not more than 01.Mpa / s rate 2.Mpa uniform boost to water pressure, and maintain 5min, the components should be no leakage, deformation or damage, such as macro-defect
1.54Mpa the device of the nitrogen or compressed air into the water immersion fire extinguishing installations, devices to level not less than the depth of 0.3m, to maintain 5min, the connected parts should be no leakage of air bubbles
Flying fire-fighting devices stent (Block) in under 5 times the quality of the fire extinguishing installations and fire extinguishing installations in the course of the jet are not allowed to have a deformed or de ring, such as the phenomenon of falling
No bubble leak
灭火机performance requirements
Ammonium dihydrogen phosphate content
第5个回答 2009-08-03
兴奋来 含泪走！ 建议花钱请专业人士翻译，最好是懂化工的，这东西含糊不得